Technical article

Catalyst poisoning: sulfur, phosphorus, nitrogen and heavy metals

Where the contaminants come from, how to confirm poisoning rather than under-dosing, and what anti-poisoning grades can and cannot fix.

Technical 7 min read24 September 2026

Catalyst poisoning is one of the least visible causes of a non-curing batch. Sulfur, phosphorus, nitrogen and heavy-metal traces deactivate the platinum complex without changing the appearance or viscosity of the compound. The batch looks normal, mixes normally and then fails in the mould or the oven. Because there is nothing to see, the catalyst usually gets blamed before the contaminant is found.

What poisoning looks like

  • A batch that starts to cross-link and then stalls, instead of never curing at all.
  • Cure that is complete at the surface but soft at the core, or uneven across a single part.
  • A formulation that cures reliably in one shift and fails in the next with the same materials.
  • A cure that completes only when the catalyst dosage is raised well above the validated level.

Where the contaminants come from

The four families behave differently and enter the process at different points. It helps to know which one is plausible before testing.

  • Sulfur: mould-release agents, sulfur-cured rubber gloves and seals nearby, some pigments and fillers, and residues from cleaning.
  • Phosphorus: flame retardants, antioxidants and plasticisers in packaging, and some phosphated additives.
  • Nitrogen: amine-cured resins, amide slip agents, polyurethane adhesives and foams, and some surfactants.
  • Heavy metals: solder, metal soaps in pigments, recycled filler and contaminated regrind.

Confirm poisoning before raising the dosage

The control test is the same one used for any curing failure. Take a known-good base, add fresh catalyst at the validated dosage and run it beside the suspect batch. If the control cures and the suspect batch does not, the base or the environment is the variable. Repeat with the suspect base and fresh catalyst: if it now cures, the catalyst lot was the problem. Only if both fresh base and fresh catalyst fail does external contamination become the leading explanation. Raising the catalyst dosage before this test can make the symptom disappear and the cause impossible to find.

A second test isolates the source: cure small samples with and without the suspect additive, glove, release agent or packaging film. A positive result for one of them points directly at the process step to change.

What anti-poisoning grades can and cannot do

PC-18B is the first-generation anti-poisoning grade. It retains stable vulcanisation activity in environments with slight to moderate poisoning impurities — trace sulfur, phosphorus and nitrogen compounds — and is a production grade available now. PC-18A is the second generation, engineered against high concentrations and multiple contaminant types. It is under final R&D: evaluation samples are available, and commercial supply is not yet committed. Neither grade can cure a base that contains no catalyst, nor compensate for an oven that never reaches temperature.

Anti-poisoning chemistry buys tolerance, not immunity. If the contamination level rises, the grade can be overwhelmed like any other. The durable fix is to reduce the source, and to use the anti-poisoning grade to cover the trace level that cannot be removed.

Reduce the source, not just the symptom

  • Change gloves and release agents to sulfur-free, non-amine types, and keep them dedicated to the silicone area.
  • Store compound and packaging away from rubber, solvents and amine-cured resins.
  • Clean mixers and moulds with a solvent that leaves no sulfur or phosphorus residue.
  • Qualify recycled filler and regrind before use, not after a failed batch.
Poisoning is a process finding, not a grade selection

If a batch fails only when a particular mould, glove or filler is used, the answer is at that process step. An anti-poisoning grade covers what cannot be eliminated; it does not replace elimination.

For potting and encapsulation, where thick sections and expensive parts make a failed pot unrecoverable, the control test should be part of the incoming-material routine rather than an emergency response. The test costs a small amount of material and one oven cycle; a lost production shift costs considerably more.

Next step

From article to evaluation sample

If this article describes your process, request a sample of the recommended grade with the matching inhibitor. Evaluation quantities ship in 5–7 days.

Technical reply within 24 hours
Evaluation samples in 5–7 days
COA, TDS and SDS on request
Custom concentration 1,000–20,000 PPM