Resources / Sample workflow

From request to production, in four steps.

A sample is only useful when it tests the right hypothesis in the right process. This workflow keeps the first trial representative: process data in, a defined grade and inhibitor pairing back, evaluation material in 5–7 days, then a scale-up path on the same chemistry.

The workflow

Four steps, one technical thread.

The same engineer reviews the request, recommends the grade and answers questions during the trial — nothing is handed to a separate sales process between sample and scale-up.

01

Request

Same business day. You send the process data: application, cure temperature, line speed, substrate and the problem the current catalyst creates. No purchase order is needed, and a mutual NDA can be signed first.

02

Evaluation

Within 24 hours. A technical engineer checks the cure window against the range, then proposes the grade, platinum concentration and inhibitor pairing with starting dosages for both components.

03

Dispatch

5–7 days. Evaluation quantities ship as a paired kit — catalyst plus enough inhibitor for a representative trial — with the COA for the lot, the TDS and the SDS. Shipments go by air with tracking.

04

Trial and scale-up

Your test schedule. You run the sample in your own formulation and oven. Technical questions are answered during the trial; when the result is accepted, the same grade is quoted in 1 kg, 5 kg and 20 kg sealed HDPE drums.

What to send

The data that changes the recommendation.

Two requests with the same application can receive different recommendations if the cure window or the contamination source differs. This checklist is the shortest version that produces a useful answer.

Process and formulation

Technical inputs.

  • Application and end product
  • Cure temperature and line speed
  • Substrate and section thickness
  • Current catalyst, concentration and dosage
  • Failure symptom: yellowing, tacky cure, short pot life, haze or poisoning
  • Target platinum concentration, if defined
  • Monthly or annual volume to size the sample
Commercial and logistics

Practical inputs.

  • Destination country, for freight and documentation
  • Required documents: TDS, SDS, COA, RoHS / REACH statement
  • Preferred packaging for the production order
  • NDA requirement, if any

If some fields are unknown, send what you have. The application and the failure symptom are enough to begin.

Sampling and freight

Free evaluation material, freight quoted before dispatch.

Evaluation quantities are supplied without charge, so the cost of a trial is lab time rather than material. Freight is confirmed case by case before the shipment leaves, because air freight pricing depends on destination, weight and service level.

Samples are typically 100–500 g of catalyst with enough inhibitor for a paired trial; larger quantities can be arranged for a pilot line. Shipments travel by air with tracking, and the SDS accompanies the sample for internal receiving and EHS review. Production orders use 1 kg, 5 kg and 20 kg sealed HDPE drums with a 6-month shelf life at 5–15°C.

What comes back

The reply package.

  • Recommended grade and platinum concentration
  • Inhibitor pairing with starting dosages
  • Sample quantity, dispatch route and freight basis
  • COA for the lot, plus TDS and SDS
  • RoHS and REACH statement where required

Technical reply within 24 hours. Samples ship in 5–7 days.

Workflow FAQ

Before you send the form.

How long does the whole process take?

The technical reply arrives within 24 hours on a business day and samples ship in 5–7 days. Custom concentrations may need a few extra days for preparation and COA. After that, the timeline belongs to your trial schedule.

Is there a charge for the sample?

Evaluation quantities are supplied free of charge. Freight is quoted case by case because it depends on destination, quantity and shipping method, and it is confirmed before dispatch rather than invoiced afterwards.

Can the sample be a custom concentration?

Yes. Custom grades from 1,000 to 20,000 PPM are prepared to order with a COA stating the measured platinum content. Allow a few extra days compared with a standard grade.

What if I do not know which grade I need?

Send the process data without a model number. The reply maps the cure window and the failure symptom to a starting grade, concentration and inhibitor pairing, so the trial tests a defined hypothesis rather than a guess.

What ships with the sample?

A paired kit: catalyst, the recommended inhibitor in a quantity sufficient for the trial, the COA for the catalyst lot, and the TDS and SDS for each grade. The lot number on the COA matches the sample label.

What a trial should answer

Three questions, one sample.

A useful evaluation answers three questions: does the grade cure fully in your process window, does it hold the property that currently fails, and does the inhibitor give a workable pot life. The sample ships with the inhibitor rather than the catalyst alone for exactly that reason.

Next step

Send the process data, not a purchase order.

Describe the application, the cure window and the symptom you are trying to fix. The technical reply will define the grade, concentration and inhibitor pairing — and the sample follows in 5–7 days.

Technical reply within 24 hours
Evaluation samples in 5–7 days
COA, TDS and SDS on request
Custom concentration 1,000–20,000 PPM