Platinum catalyst PPM: how to choose between 1,000 and 20,000
Concentration is not a quality grade. A practical way to select PPM from line speed, section thickness and inhibitor dosage.
Platinum concentration is the most quoted and least understood number on a catalyst data sheet. A 5,000 PPM grade is not better than a 1,500 PPM grade; it simply delivers more active platinum per kilogram of catalyst. Choosing a band is a process decision: how fast the compound must cross-link, how thick the section is, and how much inhibitor is holding the reaction back before the part reaches temperature.
Concentration is not a quality grade
Every grade in a concentration ladder starts from the same Karstedt's chemistry. What changes is the amount of active platinum in the supplied liquid, and therefore how much catalyst must be weighed into the compound to deliver a given platinum load. A higher concentration lets you use less catalyst liquid; it does not automatically make the compound faster, cleaner or more stable. Those properties come from the chemistry and the rest of the formulation.
Three inputs set the band
Line speed and cycle time
A line that needs cross-linking to start quickly, or a moulding cycle measured in seconds, pushes the choice toward a higher concentration or a higher-activity grade. A slow, thick-section process can use a lower band and save catalyst cost without losing output.
Section thickness
Thick sections retain heat and cure more slowly at the core, so they need a cure that keeps going once it starts. Very thin films are the opposite problem: they can dry or cross-link before the coating has levelled, and the cure window matters more than raw speed.
Inhibitor dosage
The inhibitor holds the catalyst dormant until the part reaches its activation window. If more inhibitor is used to extend bath life, more platinum may be needed to keep the same cure once the part heats. Concentration and inhibitor dosage are chosen together, not one after the other.
The practical bands
The standard range covers the most common bands. Use the table as a starting point, then confirm it with a trial on your own line.
| Band | Typical use | Trade-off |
|---|---|---|
| 1,500–2,000 PPM | Large-volume compounding, industrial moulding, cost-sensitive formulations | Lowest catalyst cost; slowest cross-linking in the standard range |
| 3,000–4,000 PPM | Balanced moulding and coating; matching an existing formulation | Moderate cost; a small step between the economy and fast grades |
| 5,000 PPM | Injection, rapid cure and high-speed coating | Fastest standard cure; highest catalyst cost per tonne |
| Custom 1,000–20,000 PPM | Thin films, unusual cycles, formulations being re-engineered | Requires a validated dosage and a check on inhibitor balance |
How to move between grades
Do not jump from one end of the ladder to the other. If the concentration doubles and the dosage is left unchanged, the platinum load doubles and the cure will be faster than the line or the inhibitor was built for. The reverse is equally common: a team moves to a lower concentration to save cost, keeps the old dosage, and reports that the new grade does not cure. Hold the delivered platinum load constant when comparing grades, then adjust dosage and inhibitor together.
A useful rule for trials is to change one variable per run. If concentration and inhibitor dosage move at the same time, the result cannot tell you which change caused the improvement or the failure.
Dosage matters as much as the label
The recommended catalyst dosage is 0.05%–0.5% of the total compound. The lower end suits high-activity grades and simple sections; the upper half is used with anti-poisoning grades or contaminated substrates. Weigh the catalyst rather than estimating it, and record the actual number in the batch sheet. A formulation that is validated at one dosage and run at another is a different formulation, even when the drum label is identical.
Anything between 1,000 and 20,000 PPM can be supplied to order. Custom concentration is a way to match the platinum load to the process, not a claim that the grade performs better than the standard ladder.
The reliable approach is to request a sample at the band you believe is right, plus the neighbouring grade, and run both against the same inhibitor dosage. The difference in cure onset and final properties then tells you which end of the ladder your process actually needs.
The grades behind this article.
1,500 PPM
The general-purpose grade. 1,500 PPM is the most widely used concentration for large-volume silicone compounding, where a predictable cure at moderate catalyst cost matters more than speed.
5,000 PPM
The high-concentration workhorse. 5,000 PPM delivers fast cross-linking for lines that need short cycle times, and it is the grade most often specified for injection and rapid-cure processes.
3,000 PPM
The middle grade, chosen when 1,500 PPM is too slow and 5,000 PPM is more catalyst than the formulation needs. A common starting point for balancing cure speed against raw-material cost.
Match the article to your formulation.
Send the process window, get a pairing recommendation.
Cure temperature, line speed, section thickness and the pot life you need are enough for a first recommendation on grade, concentration and inhibitor dosage.
Continue with the next question.
Each of these articles covers one part of the same curing system: concentration, inhibition, contamination and documentation.
Why is my silicone rubber not curing? Six root causes
Before you add more catalyst, rule out the six causes that account for most addition-cure failures — from poisoning to mixing order.
Karstedt's catalyst or peroxide cure: the real trade-offs
Why medical and food-contact silicone moved to addition cure, and where peroxide still wins on cost and tolerance.
How to extend silicone pot life without slowing the cure
The inhibitor is the control knob for working time. How dosage, type and temperature interact, with a starting matrix.
From article to evaluation sample
If this article describes your process, request a sample of the recommended grade with the matching inhibitor. Evaluation quantities ship in 5–7 days.