REACH and RoHS: a practical document checklist for silicone buyers
What a compliant supplier should be able to send you, what each document actually covers, and the claims that should raise a question.
A compliant supplier should be able to send four documents without a negotiation: a technical data sheet, a safety data sheet, a batch certificate of analysis and a RoHS / REACH statement. Each answers a different question, and each has limits. Knowing what each document covers makes it easier to spot the claims that should raise a question — and easier to hold a supplier to the ones that matter.
The four documents to ask for
For a platinum catalyst, the document pack normally contains the following. Ask for all four, and ask for the batch-linked certificate rather than a generic example.
- Technical data sheet (TDS): grade identity, platinum concentration, viscosity, appearance, dosage guidance, packaging and shelf life.
- Safety data sheet (SDS): hazard classification, handling, storage and transport information in the required language.
- Certificate of analysis (COA): the measured result for the specific batch, linked to a lot number.
- RoHS and REACH statement: the compliance position for the material as supplied.
What each document actually covers
| Document | What it covers | What it does not prove |
|---|---|---|
| TDS | Nominal specification and recommended use | That the specific drum matches the nominal value |
| SDS | Hazards, handling and transport classification | Compliance of the final cured part |
| COA | Measured values for the batch, linked to a lot | Performance in your formulation or process |
| RoHS / REACH statement | Compliance position for the material as supplied | Regulatory approval of the end device |
The COA is the document that connects a claim to a drum. A TDS states what the grade is designed to be; a COA states what a particular batch measured. If a supplier cannot link a batch number to a COA, the specification on the label is an intention rather than evidence.
Claims that should raise a question
- A certificate number that cannot be traced to a document or a batch.
- A statement that the catalyst itself is approved for a medical device. Clearance applies to the medical end device, not to a raw material; the catalyst's role is described by the end-device category, not claimed as an approval.
- A percentage or a limit that is not defined — compliance with which regulation, for which substance, at which threshold.
- A RoHS or REACH statement describing the finished part when the question was about the material supplied.
- A statement that is out of date, or copied from a different grade.
How to read a RoHS and REACH statement
The useful wording is specific and modest: the material as supplied is compliant with RoHS and REACH. It does not need a certificate number to be meaningful, and it should not claim one that cannot be checked. The statement covers the material supplied; the compliance of the cured part depends on the whole formulation, the fillers, the pigments and the process. For a medical or food-contact end device, the regulatory work belongs to the device, and the supplier's contribution is documentation of the material.
Ask also for the statement to name the grade. A statement that applies to silicone products in general is not a statement about the catalyst you are buying. If the grade changes, the statement should be reissued for the new grade.
Build the pack into the purchase
The simplest way to avoid a documentation problem is to make the pack part of the purchase order: TDS and SDS with the quotation, COA with each batch, and the RoHS / REACH statement reissued when the grade or the regulation changes. That is also the point at which a missing document is easy to fix, rather than at incoming inspection when a line is waiting.
The material statement says what the catalyst is; the end-device qualification says what the finished product is. Do not accept one as evidence of the other.
A supplier who is comfortable with that separation is usually also comfortable being asked for the batch-level data behind the COA. Both are good signs.
The grades behind this article.
Match the article to your formulation.
Send the process window, get a pairing recommendation.
Cure temperature, line speed, section thickness and the pot life you need are enough for a first recommendation on grade, concentration and inhibitor dosage.
Continue with the next question.
Each of these articles covers one part of the same curing system: concentration, inhibition, contamination and documentation.
Why is my silicone rubber not curing? Six root causes
Before you add more catalyst, rule out the six causes that account for most addition-cure failures — from poisoning to mixing order.
Platinum catalyst PPM: how to choose between 1,000 and 20,000
Concentration is not a quality grade. A practical way to select PPM from line speed, section thickness and inhibitor dosage.
Anti-yellowing catalyst for PPF: what the ΔE data actually shows
ΔE 0.8 against 4.2 after 48 hours at 85°C — how the test is run, what it does and does not predict, and how to reproduce it.
From article to evaluation sample
If this article describes your process, request a sample of the recommended grade with the matching inhibitor. Evaluation quantities ship in 5–7 days.